Longbow DIY Headlining Replacement by Geoff Mcdonough

Like most Westerlys of the 1970s the head lining had drooped and was looking tired this is caused by the foam backing braking down into a sticky dust and separating from the fibreglass. I had looked into various ways of solving the problem including sticking original vinyl back up directly to the inside cabin but this looked untidy and not very smooth also depending upon the glue the vinyl would stretch. I also tried using roll of the stuff used under laminate flooring as a base layer then gluing the original vinyl to that but again although better this still looked untidy as the old vinyl was stained in places.

Now that I had decided that I was not going to reuse the old vinyl it was time to remove it and its backing. This is the worst part of the job fortunately the foam had disintegrated so much that most of it came off with the vacuum cleaner although it is quite sticky its nasty stuff so gloves goggles and mask are advisable. Once it was all removed there was still glue residue left I tried cellulose thinners on a cloth at first but raw fibre glass is not something you want to be rubbing due to loose fibres sticking in your fingers so I used an angle grinder with a wire brush on again this was messy but got most of it off.

By now I had realised that due to the rough nature of the glass fibre mouldings I would need to have some sort of foam insulation/padding. Whilst researching this on the net some one mentioned using camping mats from the pound shop. This was a stroke of genius as this material is about 10mm thick and soft and mouldable and very cheap. At about the same time I had seen some van lining material on the internet called Veltrim (ring Chris on Phone number available to members) which is a felt material available in a number of colours. I had seen this fitted in minibuses and it gave a good finish which is warm to the touch.

That was the materials sorted now to find a suitable adhesive for the foam as the Veltrim comes with its own glue. I first tried liquid contact adhesive this was difficult to apply and strong smelling next I tried a water based carpet adhesive* which is applied using a combed trowel this looked ok to start with but after a week it still had not dried out. Finally I tried spray on contact adhesive similar to that supplied with the Veltrim although initially I was not too keen as it’s being used in a confined space but having all the hatches open helped and it was not too bad but plenty of breaks for fresh air is advisable**. With a bit of practice it is quite easy get the spray where you want it without to much mess and any over spray was cleaned up using thinners.

First I sprayed the back of the foam then the roof and left for 2 minutes to allow the spirit to evaporate then stick the foam down and trim to size. In places where there were bolt heads from deck fittings protruding I put on circular patches of foam first to even out the indentations.

When the whole area had been lined with foam I left it until the next weekend to allow it to fully dry out and to see if anything moved or came loose fortunately nothing did. Now onto the lining material this is fitted the same way using the supplied spray glue spraying the roof and the material then letting it dry for 2 minutes then sticking it in place. This glue unlike liquid contact adhesive allows you to reposition the piece a number of times until it is in the correct position which is useful. The roof of the fore cabin was done in two pieces this was for ease of handling in such a confined space and also to save on waste as its two triangles cut in opposite directions.

The sides of the bunks were originally finished in gel coat which was in good condition but was cold if you rolled against it through the night so I decided to cover these as well. I felt that the foam was not required for this area as the surface was smooth to start with.

After a bit of trail and error I found that the best way of cutting the material to size was to glue it in place and push into the corners using a straight edge or rounded rod and cutting in with a sharp Stanley knife.

After re-varnishing all of the wooden trim and refitting this on top of the Veltrim I finally fitted the reupholstered cushions. The finished job looks professional and should be much warmer whilst cutting down on condensation. The total cost of the job was around £120 which is not bad considering the difference it has made to the over all look of the interior.

Tech Editor’s Notes
* High temperature adhesive variants are preferable for under deck areas that become hot in the sun.
**Wearing a mask which has a chemical filter is strongly recommended.

[envira-gallery id=”118206″]